The Lumen Subsea Light is a blindingly bright LED light for use on ROVs, AUVs, and other subsea applications. We designed this light specifically for this purpose and it has a few neat features:
- Fully dimmable control using a PWM servo signal (1100-1900 μs)
- Simple on/off control with no signal needed
- Daisy-chainable to connect multiple lights from a single connection
- Automatic, smart over-temperature compensation for maximum light output and safety in air
- New in R2: Built-in mounting holes on the side of the case (M3 thread)
- New in R2: Exponential brightness control with much lower minimum brightness output
- New in R2: 950m depth rating
Using a high-efficiency Cree XLamp MK-R LED, the light outputs over 1500 lumens at 15 Watts – brighter than most car headlights! It has a 135 degree beam angle for wide illumination in front of an ROV. The color temperature is 6200K, similar to most dive lights and ROV lights.
In addition to really high brightness, the Lumen R2 is designed for very low brightness output, which is important to be able to illuminate the scene without washing out the colors or brightness. An exponential brightness curve makes it intuitive to use effectively.
It’s housed in a rugged hard-anodized aluminum enclosure with two cable penetrators at the rear, allowing it to go to a depth of 950m. By default, the second cable penetrator is blank, but the light comes with a second penetrator to allow a second light to be connected to the first (daisy-chaining). That means you only need one cable coming from the main watertight enclosure to control multiple lights!
The specially designed injection molded acrylic lens ensures a consistent beam angle in both air and water. The case has a built-in mounting bracket with two M3 threaded holes for mounting to your vehicle.
For those who want to use the light in other applications, like scuba diving, the light can be operated without a PWM signal. Just connect the yellow signal wire to the power wire and it will turn on! A switch can be used here to make this even more convenient.
The light operates on 10-48V inputs and can accept PWM signals from 3-48V! It is compatible with many common boards like the Arduino, Raspberry Pi, and PixHawk. The case warms up to a comfortable 55°C (131°F) when operated in air and stays much cooler in water.
Note: We recommend that you don’t look directly into this light to avoid any damage to your eyes!
- 1 x Lumen Subsea Light
- 2 x Stainless steel M3 mounting screws
- 1 x Lumen Cable Penetrator for 4mm Cable
- 1 x O-ring for Lumen Cable Penetrator
|Supply Voltage (V in )||7 – 48 volts|
|Full Brightness Supply Voltage (V in )||10 – 48 volts|
|PWM Logic Voltage||3 – 48 volts|
|Peak Current||15 / V in amps|
|Maximum Brightness||1,500 lumens|
|Color Temperature||6,200 kelvin|
|Beam Angle||135 degrees in water|
|Cable Diameter||4.3 mm||0.17 in|
|Cable Length||1 m||39 in|
|Cable Jacket||Black Urethane|
|Conductor Gauge||22 AWG|
|Wires||Black – Ground|
|Red – Power|
|Yellow – Signal|
|Pressure Rating||950 m||3120 ft|
|Overall Length||68.9 mm||2.71 in|
|Overall Diameter||37 mm||1.46 in|
|Bracket Mounting Hole Spacing||19 mm||0.75 in|
|Bracket Screw Size||M3|
|Weight in Air (w/ 1m cable)||102 g||3.60 oz|
|Weight in Water (w/ 1m cable)||53 g||1.87 oz|
|Maximum Temperature when Run in Air||55° C||130° F|
|Dimensions||11.5 × 7.5 × 4 cm|